One-Click Measurement Operation, Automatic Power Off After Delay. The Shutdown Current Is Only 20na, Supporting Battery Operation. Supports The Measurement Of Two Resistors, And The Potentiometer Can Also Be Measured. If The Potentiometer Is Adjusted To One End Of It, The Tester Cannot Distinguish Between The Pins In The Middle And The Ends. The Resolution Of Resistance Measurement Is 0.1 , And The Highest Measured Value Reaches 50m . Automatically Detect Pnp And Npn Bipolar Transistors, N And P Channel Mosfets, Jfet Field Effect Transistors, Diodes, Dual Diodes, Thyristors, Resistors, Capacitors, And Inductors. Automatically Detect Pin Definitions.Measure The Current Amplification Factor (B) Of The Bipolar Transistor And The Turn-On Voltage (Uf) Of The Emitter Junction. Transistors Can Be Identified By Their High Threshold Voltage And High Current Amplification Factor. Capacitance Measurement Range Is From 25pf To 100mf (100, 000Uf). The Resolution Can Reach 1Pf,And The Inductance Measurement Range Is 0.01mh-20h.Otherwise,Will Displayed As Resistance.If The Dc Resistance Value Of Inductor Is Higher Than 2100s,It Will Also Be Displayed As Resistance.When Testing The Capacitor, Vloss Displayed On The Screen Means Loss And Attenuation. The Larger Value,The Closer The Capacitor Is To Scrapping!Esr Is Impedance.The Smaller Value,The Better Capacitor Performance! The Protection Diodes Inside Bipolar Transistors And Mosfets Can Be Detected And Displayed On The Screen. It Can Detect The Equivalent Series Resistance (ESR) Of Capacitors Above 2uf With A Resolution Of 0.01 . This Feature Is Very Important For Testing Capacitor Performance. It Is Possible To Display The Correct Direction Sign For Both Diodes, As Well As The Forward Voltage Drop. Measure The Threshold Voltage And Gate Capacitance Of The Mosfet. The Led Is Detected As A Diode, AndThe Forward Voltage Drop Is Higher Than The Normal Value. Dual Led Detection Is Dual Diode. The Led Will Flash During Detection. The Time Of Each Test Is About Two Seconds, Only Capacitance And Inductance Measurements Will Take Longer Description: Power Supply: DC9V (You Need To Bring Your Own 9V Laminated Battery 6F22) Simple Operation Instructions: Connect Pins 1, 2, And 3 At Will, Automatically Identify The Type, Automatically Detect The Pin Sequence, Graphic Display, And Automatically Measure Parameters. Test Scope Description: 1. Transistor Range: Transistors Composed Of Less Than 2 (Including 2) Pn Junctions, And Do Not Have Other Resistor-Capacitor Components Inside. 2. Resistance Measurement 0.5-50m 3. Inductance Measurement 0.01mH-20h 4. Capacitance Measurement 25pf - 100000uf Note: Different Batches May Have Differences In Product Appearance, Color, And Printed Characters, Which Will Not Affect The Use Material: ABS colour: As Shown Package Contents: 1 x Transistor Tester 1 x Socket Only the above package content, other products are not included. Note: Light reflection and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
One-Click Measurement Operation, Automatic Power Off After Delay. The Shutdown Current Is Only 20na, Supporting Battery Operation. Supports The Measurement Of Two Resistors, And The Potentiometer Can Also Be Measured. If The Potentiometer Is Adjusted To One End Of It, The Tester Cannot Distinguish Between The Pins In The Middle And The Ends. The Resolution Of Resistance Measurement Is 0.1 , And The Highest Measured Value Reaches 50m . Automatically Detect Pnp And Npn Bipolar Transistors, N And P Channel Mosfets, Jfet Field Effect Transistors, Diodes, Dual Diodes, Thyristors, Resistors, Capacitors, And Inductors. Automatically Detect Pin Definitions.Measure The Current Amplification Factor (B) Of The Bipolar Transistor And The Turn-On Voltage (Uf) Of The Emitter Junction. Transistors Can Be Identified By Their High Threshold Voltage And High Current Amplification Factor. Capacitance Measurement Range Is From 25pf To 100mf (100, 000Uf). The Resolution Can Reach 1Pf,And The Inductance Measurement Range Is 0.01mh-20h.Otherwise,Will Displayed As Resistance.If The Dc Resistance Value Of Inductor Is Higher Than 2100s,It Will Also Be Displayed As Resistance.When Testing The Capacitor, Vloss Displayed On The Screen Means Loss And Attenuation. The Larger Value,The Closer The Capacitor Is To Scrapping!Esr Is Impedance.The Smaller Value,The Better Capacitor Performance! The Protection Diodes Inside Bipolar Transistors And Mosfets Can Be Detected And Displayed On The Screen. It Can Detect The Equivalent Series Resistance (ESR) Of Capacitors Above 2uf With A Resolution Of 0.01 . This Feature Is Very Important For Testing Capacitor Performance. It Is Possible To Display The Correct Direction Sign For Both Diodes, As Well As The Forward Voltage Drop. Measure The Threshold Voltage And Gate Capacitance Of The Mosfet. The Led Is Detected As A Diode, AndThe Forward Voltage Drop Is Higher Than The Normal Value. Dual Led Detection Is Dual Diode. The Led Will Flash During Detection. The Time Of Each Test Is About Two Seconds, Only Capacitance And Inductance Measurements Will Take Longer Description: Power Supply: DC9V (You Need To Bring Your Own 9V Laminated Battery 6F22) Simple Operation Instructions: Connect Pins 1, 2, And 3 At Will, Automatically Identify The Type, Automatically Detect The Pin Sequence, Graphic Display, And Automatically Measure Parameters. Test Scope Description: 1. Transistor Range: Transistors Composed Of Less Than 2 (Including 2) Pn Junctions, And Do Not Have Other Resistor-Capacitor Components Inside. 2. Resistance Measurement 0.5-50m 3. Inductance Measurement 0.01mH-20h 4. Capacitance Measurement 25pf - 100000uf Note: Different Batches May Have Differences In Product Appearance, Color, And Printed Characters, Which Will Not Affect The Use Material: ABS colour: As Shown Package Contents: 1 x Transistor Tester 1 x Socket Only the above package content, other products are not included. Note: Light reflection and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
Sellers offer a range of delivery options, so you can choose the one thatâs most convenient for you. Many sellers offer free delivery. You can always find the postage cost and estimated delivery date in a sellerâs listing. You'll then be able to see a full list of delivery options during checkout. These can include: Express delivery, Standard delivery, Economy delivery, Click & Collect, Free local collection from seller.
Your options for returning an item vary depending on what you want to return, why you want to return it, and the seller's return policy. If the item is damaged or doesn't match the listing description, you can return it even if the seller's returns policy says they don't accept returns. If you've changed your mind and no longer want an item, you can still request a return, but the seller doesn't have to accept it. If the buyer changes their mind about a purchase and wants to return an item, they may need to pay return postage costs, depending on the seller's return policy. Sellers can provide a return postage address and additional return postage information for the buyer. Sellers pay for return postage if there's a problem with the item. For example, if the item doesn't match the listing description, is damaged or defective or is counterfeit. By law, customers in the European Union also have the right to cancel the purchase of an item within 14 days beginning from the day you receive, or a third party indicated by you (other than the carrier) receives, the last good ordered by you (if delivered separately). This applies to all products except for digital items (e.g. Digital Music) that are provided immediately to you with your acknowledgement, and other items such as video, DVD, audio, video games, Sex and Sensuality products and software products where the item has been unsealed.
Sellers have to offer a refund for certain items only if they are faulty, such as: Personalised items and custom-made items, Perishable items, Newspapers and magazines, Unwrapped CDs DVDs and computer software. If you used your PayPal balance or bank account to fund the original payment, the refunded money will go back to your PayPal account balance. If you used a credit or debit card to fund the original payment, the refunded money will go back to your card. The seller will effect the refund within three working days but it may take up to 30 days for Paypal to process the transfer. For payments funded partially by a card and partially by your balance/bank, the money taken from your card will go back to your card and the remainder will return to your PayPal balance.