Floplast Shallow Bath Trap (Dia)40Mm White
Bath traps traditionally only have a 20mm deep seal. This is because there is very little chance of induced siphonage (and hence loss of trap seal) because the flat bottom of the bath ensures that water flows out through the waste at a much slower rate than in a basin or sink. The outlet size of this trap is 40mm.This trap is manufactured by FloPlast, one of the UKandrsquo;s leading suppliers of above and below ground drainage systems. It can be connected to most UK manufacturersandrsquo; push fit and solvent weld waste pipes.To connect the trap, always start at the top with the connection to the waste fitting. If the installation is particularly tight we suggest assembling all connections loosely before finally tightening all nuts once the trap is in position.First you should ensure that the O ring is correctly seated on its lug inside the top trap nut. Push the lug inside the waste fitting and tighten the nut by hand. Do not overtighten as this could damage the O ring. To connect the other end to the waste pipe, unscrew the nut from the trap and remove it along with the washer and the rubber seal. Place these three components over the end of the pipe andndash; first the nut, then the washer followed by the seal. Push the pipe into the trap as far as it will go, slide the seal and washer forward into position and tighten the nut. On all traps, double check that the central joint in the body of the trap is tight. All joints can be taken apart again if required, but always check that the rubber seal has not been damaged in any way as this will cause the joint to leak.Click here to watch our video showing how to install a trap.
Price now:
From
£4.00
to
£6.60
Price History:
Details:Floplast Shallow Bath Trap (Dia)40Mm White
Bath traps traditionally only have a 20mm deep seal. This is because there is very little chance of induced siphonage (and hence loss of trap seal) because the flat bottom of the bath ensures that water flows out through the waste at a much slower rate than in a basin or sink. The outlet size of this trap is 40mm.This trap is manufactured by FloPlast, one of the UKandrsquo;s leading suppliers of above and below ground drainage systems. It can be connected to most UK manufacturersandrsquo; push fit and solvent weld waste pipes.To connect the trap, always start at the top with the connection to the waste fitting. If the installation is particularly tight we suggest assembling all connections loosely before finally tightening all nuts once the trap is in position.First you should ensure that the O ring is correctly seated on its lug inside the top trap nut. Push the lug inside the waste fitting and tighten the nut by hand. Do not overtighten as this could damage the O ring. To connect the other end to the waste pipe, unscrew the nut from the trap and remove it along with the washer and the rubber seal. Place these three components over the end of the pipe andndash; first the nut, then the washer followed by the seal. Push the pipe into the trap as far as it will go, slide the seal and washer forward into position and tighten the nut. On all traps, double check that the central joint in the body of the trap is tight. All joints can be taken apart again if required, but always check that the rubber seal has not been damaged in any way as this will cause the joint to leak.Click here to watch our video showing how to install a trap.
Price now:
From
£4.00
to
£6.60
Professional Building Supplies
0.00% (~ £0.00)
New
£6.60
New | £4.00Free Delivery | Store |
New | £4.00Free Delivery | Store |
Professional Building Supplies | £6.60Free Delivery | Store |
Product Description
Bath traps traditionally only have a 20mm deep seal. This is because there is very little chance of induced siphonage (and hence loss of trap seal) because the flat bottom of the bath ensures that water flows out through the waste at a much slower rate than in a basin or sink. The outlet size of this trap is 40mm.This trap is manufactured by FloPlast, one of the UKandrsquo;s leading suppliers of above and below ground drainage systems. It can be connected to most UK manufacturersandrsquo; push fit and solvent weld waste pipes.To connect the trap, always start at the top with the connection to the waste fitting. If the installation is particularly tight we suggest assembling all connections loosely before finally tightening all nuts once the trap is in position.First you should ensure that the O ring is correctly seated on its lug inside the top trap nut. Push the lug inside the waste fitting and tighten the nut by hand. Do not overtighten as this could damage the O ring. To connect the other end to the waste pipe, unscrew the nut from the trap and remove it along with the washer and the rubber seal. Place these three components over the end of the pipe andndash; first the nut, then the washer followed by the seal. Push the pipe into the trap as far as it will go, slide the seal and washer forward into position and tighten the nut. On all traps, double check that the central joint in the body of the trap is tight. All joints can be taken apart again if required, but always check that the rubber seal has not been damaged in any way as this will cause the joint to leak.Click here to watch our video showing how to install a trap.
Product Specifications
General | |
|---|---|
Size | One Size |
Material | polypropylene |
Brand | FloPlast |
Related Products
Delivery, Returns & Refunds
Delivery
Sellers offer a range of delivery options, so you can choose the one that’s most convenient for you. Many sellers offer free delivery. You can always find the postage cost and estimated delivery date in a seller’s listing. You'll then be able to see a full list of delivery options during checkout. These can include: Express delivery, Standard delivery, Economy delivery, Click & Collect, Free local collection from seller.
Returns
Your options for returning an item vary depending on what you want to return, why you want to return it, and the seller's return policy. If the item is damaged or doesn't match the listing description, you can return it even if the seller's returns policy says they don't accept returns. If you've changed your mind and no longer want an item, you can still request a return, but the seller doesn't have to accept it. If the buyer changes their mind about a purchase and wants to return an item, they may need to pay return postage costs, depending on the seller's return policy. Sellers can provide a return postage address and additional return postage information for the buyer. Sellers pay for return postage if there's a problem with the item. For example, if the item doesn't match the listing description, is damaged or defective or is counterfeit. By law, customers in the European Union also have the right to cancel the purchase of an item within 14 days beginning from the day you receive, or a third party indicated by you (other than the carrier) receives, the last good ordered by you (if delivered separately). This applies to all products except for digital items (e.g. Digital Music) that are provided immediately to you with your acknowledgement, and other items such as video, DVD, audio, video games, Sex and Sensuality products and software products where the item has been unsealed.
Refunds
Sellers have to offer a refund for certain items only if they are faulty, such as: Personalised items and custom-made items, Perishable items, Newspapers and magazines, Unwrapped CDs DVDs and computer software. If you used your PayPal balance or bank account to fund the original payment, the refunded money will go back to your PayPal account balance. If you used a credit or debit card to fund the original payment, the refunded money will go back to your card. The seller will effect the refund within three working days but it may take up to 30 days for Paypal to process the transfer. For payments funded partially by a card and partially by your balance/bank, the money taken from your card will go back to your card and the remainder will return to your PayPal balance.