GAS SPRING BONNET 8004218 FOR AUDI A6/S6/Allroad BPJ/BYK 2.0L CAHB/CAHA 2.0L A6
ROC produces a comprehensive range of OE-matching quality gas springs, most complete with end fittings and covering almost every European & Asian vehicle. Gas Springs are pivotal components in vehicles, employing a steel cylinder filled with high-pressure nitrogen gas, a small amount of oil, a piston, piston rod, seals, and end fittings. These springs facilitate the controlled opening and closing of a vehicle's boot or bonnet, supporting their weight when open. The piston's design ensures that gas pressure forces it and the rod to full extension. Gas spring specifications are tailored to each application's weight requirements, adjusting piston areas and gas pressure accordingly. Manufacturing gas springs involves high-quality materials, with tubes made from pressure vessel steel, finely ground and polished steel bars for piston rods, and special, wear-resistant materials for rod guides and gaskets. The cylinders are painted with corrosion-inhibiting paint, and each gas spring undergoes rigorous load, deflection, and speed testing to ensure quality. ROC's attention to detail and testing procedures provide lifetime assurance, with each spring clearly marked for easy identification. Safety Gas springs contain oil and pressurised gas. Never attempt to open or drill into a gas spring. For safety, spring installation should be undertaken by a competent person and instructions from a recognised repair manual should be followed. Compare the design, length, and end fittings against the existing spring. Check the mounting points on the vehicle's body are clean and in good condition. If damaged, they should be changed or repaired before the replacement spring is installed. Gas springs support the weight of a vehicle's boot or bonnet. To avoid injuries, always ensure that the boot or bonnet is secured before replacing springs. Where the end fitting is a 'ball and socket'Ā design, it is important that the safety clips are correctly located after fitting. Where applicable, we recommend that gas springs are replaced in pairs. Design Gas springs consist of a pressure tube, piston rod, piston, seals, and other components. They contain a small amount of oil that produces a damping effect, as well as keeping the sealslubricated. Gas springs are filled with compressed nitrogen, which forces the piston rod to extend once compressed. The gas pressure within the spring is set to provide the correct force, based on the weight ofthe boot or bonnet. Cold temperatures reduce the lifting capabilities of gas springs - the force stated on a gas spring is established at a temperature of 20Ā°C and the operating force of the spring will then alter depending on the environmental temperatures during use, with variation at a rate of +/- 0.34% per change in degree Celsius. ROC gas springs are made in accordance with ISO9001 & ISO14001. ROC gas springs are inspected and tested before delivery.
Price now:
From
Ā£19.90
To
Ā£34.22
Price History:
Details:GAS SPRING BONNET 8004218 FOR AUDI A6/S6/Allroad BPJ/BYK 2.0L CAHB/CAHA 2.0L A6
ROC produces a comprehensive range of OE-matching quality gas springs, most complete with end fittings and covering almost every European & Asian vehicle. Gas Springs are pivotal components in vehicles, employing a steel cylinder filled with high-pressure nitrogen gas, a small amount of oil, a piston, piston rod, seals, and end fittings. These springs facilitate the controlled opening and closing of a vehicle's boot or bonnet, supporting their weight when open. The piston's design ensures that gas pressure forces it and the rod to full extension. Gas spring specifications are tailored to each application's weight requirements, adjusting piston areas and gas pressure accordingly. Manufacturing gas springs involves high-quality materials, with tubes made from pressure vessel steel, finely ground and polished steel bars for piston rods, and special, wear-resistant materials for rod guides and gaskets. The cylinders are painted with corrosion-inhibiting paint, and each gas spring undergoes rigorous load, deflection, and speed testing to ensure quality. ROC's attention to detail and testing procedures provide lifetime assurance, with each spring clearly marked for easy identification. Safety Gas springs contain oil and pressurised gas. Never attempt to open or drill into a gas spring. For safety, spring installation should be undertaken by a competent person and instructions from a recognised repair manual should be followed. Compare the design, length, and end fittings against the existing spring. Check the mounting points on the vehicle's body are clean and in good condition. If damaged, they should be changed or repaired before the replacement spring is installed. Gas springs support the weight of a vehicle's boot or bonnet. To avoid injuries, always ensure that the boot or bonnet is secured before replacing springs. Where the end fitting is a 'ball and socket'Ā design, it is important that the safety clips are correctly located after fitting. Where applicable, we recommend that gas springs are replaced in pairs. Design Gas springs consist of a pressure tube, piston rod, piston, seals, and other components. They contain a small amount of oil that produces a damping effect, as well as keeping the sealslubricated. Gas springs are filled with compressed nitrogen, which forces the piston rod to extend once compressed. The gas pressure within the spring is set to provide the correct force, based on the weight ofthe boot or bonnet. Cold temperatures reduce the lifting capabilities of gas springs - the force stated on a gas spring is established at a temperature of 20Ā°C and the operating force of the spring will then alter depending on the environmental temperatures during use, with variation at a rate of +/- 0.34% per change in degree Celsius. ROC gas springs are made in accordance with ISO9001 & ISO14001. ROC gas springs are inspected and tested before delivery.
Price now:
From
Ā£19.90
To
Ā£34.22
eBay
New
Ā£19.90
eBay
New
Ā£22.12
Ā£29.42
eBay
New
Ā£27.08
eBay
New
Ā£27.08
eBay
New
Ā£27.95
eBay
New
Ā£29.57
eBay
New
Ā£30.55
eBay
New
Ā£34.22
Currently Unavailable
Product Description
ROC produces a comprehensive range of OE-matching quality gas springs, most complete with end fittings and covering almost every European & Asian vehicle. Gas Springs are pivotal components in vehicles, employing a steel cylinder filled with high-pressure nitrogen gas, a small amount of oil, a piston, piston rod, seals, and end fittings. These springs facilitate the controlled opening and closing of a vehicle's boot or bonnet, supporting their weight when open. The piston's design ensures that gas pressure forces it and the rod to full extension. Gas spring specifications are tailored to each application's weight requirements, adjusting piston areas and gas pressure accordingly. Manufacturing gas springs involves high-quality materials, with tubes made from pressure vessel steel, finely ground and polished steel bars for piston rods, and special, wear-resistant materials for rod guides and gaskets. The cylinders are painted with corrosion-inhibiting paint, and each gas spring undergoes rigorous load, deflection, and speed testing to ensure quality. ROC's attention to detail and testing procedures provide lifetime assurance, with each spring clearly marked for easy identification. Safety Gas springs contain oil and pressurised gas. Never attempt to open or drill into a gas spring. For safety, spring installation should be undertaken by a competent person and instructions from a recognised repair manual should be followed. Compare the design, length, and end fittings against the existing spring. Check the mounting points on the vehicle's body are clean and in good condition. If damaged, they should be changed or repaired before the replacement spring is installed. Gas springs support the weight of a vehicle's boot or bonnet. To avoid injuries, always ensure that the boot or bonnet is secured before replacing springs. Where the end fitting is a 'ball and socket'Ā design, it is important that the safety clips are correctly located after fitting. Where applicable, we recommend that gas springs are replaced in pairs. Design Gas springs consist of a pressure tube, piston rod, piston, seals, and other components. They contain a small amount of oil that produces a damping effect, as well as keeping the sealslubricated. Gas springs are filled with compressed nitrogen, which forces the piston rod to extend once compressed. The gas pressure within the spring is set to provide the correct force, based on the weight ofthe boot or bonnet. Cold temperatures reduce the lifting capabilities of gas springs - the force stated on a gas spring is established at a temperature of 20Ā°C and the operating force of the spring will then alter depending on the environmental temperatures during use, with variation at a rate of +/- 0.34% per change in degree Celsius. ROC gas springs are made in accordance with ISO9001 & ISO14001. ROC gas springs are inspected and tested before delivery.
Product Specifications
General | |
|---|---|
type | bonnet gas strut |
Brand | Kilen |
Category | body |
Material | steel |
Size | small |
Delivery, Returns & Refunds
Delivery
Sellers offer a range of delivery options, so you can choose the one thatās most convenient for you. Many sellers offer free delivery. You can always find the postage cost and estimated delivery date in a sellerās listing. You'll then be able to see a full list of delivery options during checkout. These can include: Express delivery, Standard delivery, Economy delivery, Click & Collect, Free local collection from seller.
Returns
Your options for returning an item vary depending on what you want to return, why you want to return it, and the seller's return policy. If the item is damaged or doesn't match the listing description, you can return it even if the seller's returns policy says they don't accept returns. If you've changed your mind and no longer want an item, you can still request a return, but the seller doesn't have to accept it. If the buyer changes their mind about a purchase and wants to return an item, they may need to pay return postage costs, depending on the seller's return policy. Sellers can provide a return postage address and additional return postage information for the buyer. Sellers pay for return postage if there's a problem with the item. For example, if the item doesn't match the listing description, is damaged or defective or is counterfeit. By law, customers in the European Union also have the right to cancel the purchase of an item within 14 days beginning from the day you receive, or a third party indicated by you (other than the carrier) receives, the last good ordered by you (if delivered separately). This applies to all products except for digital items (e.g. Digital Music) that are provided immediately to you with your acknowledgement, and other items such as video, DVD, audio, video games, Sex and Sensuality products and software products where the item has been unsealed.
Refunds
Sellers have to offer a refund for certain items only if they are faulty, such as: Personalised items and custom-made items, Perishable items, Newspapers and magazines, Unwrapped CDs DVDs and computer software. If you used your PayPal balance or bank account to fund the original payment, the refunded money will go back to your PayPal account balance. If you used a credit or debit card to fund the original payment, the refunded money will go back to your card. The seller will effect the refund within three working days but it may take up to 30 days for Paypal to process the transfer. For payments funded partially by a card and partially by your balance/bank, the money taken from your card will go back to your card and the remainder will return to your PayPal balance.